Hubble Lithium
  • Home
  • PRODUCTS
    • Solar Lithium Batteries
    • Golf Cart Lithium Batteries
  • Inverter Guides
    • Axpert
    • Deye
    • GoodWe
    • Growatt
    • Kodak
    • Luxpower
    • Mecer
    • Microcare
    • MLT
    • Must
    • Phocos
    • SUNSYNK >
      • Sunsynk 8KW & 12KW Setup
      • Sunsynk 5KW Setup
    • Synapse
    • Victron
  • Cloudlink
    • HUBBLE Cloudlink
    • Setup Guide
    • CLOUDLINK PORTAL >
      • PORTAL LOGIN
      • CHANGE LOG
  • About
    • Team
    • News & Updates
  • Contact
  • Reseller
    • Reseller Registration
    • Reseller Access
    • Downloads

GOODWE INVERTER SETUP

The GoodWe inverters are fully compatible with the Hubble range of batteries. 
The following field guide will assist with the correct battery settings you should use.
For further detailed information ensure you read the manual of the supplied battery regarding the setup and installation instructions.

GOODWE INVERTER

Picture

 GOODWE INVERTER

Picture
Picture

GOODWE INVERTER & HUBBLE
​PRE-LAUNCH SETUP

Download the corresponding Hubble product manual and check the installation guide and pre-launch checklist.
​

GOODWE INVERTER SETTINGS

The below settings are the recommended settings to use for the corresponding Hubble Lithium battery, as seen on the PV Master App.
Picture
DOWNLOAD PV MASTER FOR IOS
DOWNLOAD PV MASTER FOR ANDROID
Picture
OPERATION MODE
Picture
SYSTEM DATA
Picture
WORK STATUS

HUBBLE LITHIUM & GOODWE PIN LAYOUTS

Below are the Hubble BMS, Cloudlink, and Goodwe side pinouts.
Note that the Hubble Lithium BMS pinouts are the same as the Cloudlink CAN pinouts.
Picture

FREQUENTLY ASKED SUNSYNK QUESTIONS

Q: How do you setup multiple batteries?

​A: Check the manual for a more detailed explanation. You will have to set dip switch settings per battery to give them a unique address. You also have to connect the included RJ45 battery link cables into the "Battery Link" port of each battery. Ensure your master battery dip switch 1 is on, 2,3,4 is OFF.  Only the master battery CAN Bus will be enabled. You can then connect the Cloudlink into the CAN port of the master battery for communications to work.

Q: Do I have to use the communication battery link cables if i dont want to monitor or have communications?

​A: Short answer No. However it is recommended to still connect the battery links and set the correct addresses. This also needs to be done if you want to connect a Hubble Cloudlink.

HUBBLE DIP SWITCH SETTINGS FOR MULTIPLE BATTERY INSTALLATION

Picture
Picture
​For correct setup and communication each battery needs a unique serial address in order to communicate.
If you are only using one battery in your setup, consider this the master battery and ensure you set it to address 1.

CONTACT US

​BECOME A RESELLER

RESELLER LOGIN

Picture

VIEW OUR PRODUCTS

ABOUT HUBBLE-RIOT CLOUDLINK

SUPPORT

Copyright Hubble Lithium (pty) ltd 2020 - 2021
  • Home
  • PRODUCTS
    • Solar Lithium Batteries
    • Golf Cart Lithium Batteries
  • Inverter Guides
    • Axpert
    • Deye
    • GoodWe
    • Growatt
    • Kodak
    • Luxpower
    • Mecer
    • Microcare
    • MLT
    • Must
    • Phocos
    • SUNSYNK >
      • Sunsynk 8KW & 12KW Setup
      • Sunsynk 5KW Setup
    • Synapse
    • Victron
  • Cloudlink
    • HUBBLE Cloudlink
    • Setup Guide
    • CLOUDLINK PORTAL >
      • PORTAL LOGIN
      • CHANGE LOG
  • About
    • Team
    • News & Updates
  • Contact
  • Reseller
    • Reseller Registration
    • Reseller Access
    • Downloads