Hubble Lithium
  • Home
  • PRODUCTS
    • Solar Lithium Batteries
    • Golf Cart Lithium Batteries
  • Inverter Guides
    • Axpert
    • Deye
    • GoodWe
    • Growatt
    • Kodak
    • Luxpower
    • Mecer
    • Microcare
    • MLT
    • Must
    • Phocos
    • SUNSYNK >
      • Sunsynk 8KW & 12KW Setup
      • Sunsynk 5KW Setup
    • Synapse
    • Victron
  • Cloudlink
    • HUBBLE Cloudlink
    • Setup Guide
    • CLOUDLINK PORTAL >
      • PORTAL LOGIN
      • CHANGE LOG
  • About
    • Team
    • News & Updates
  • Contact
  • Reseller
    • Reseller Registration
    • Reseller Access
    • Downloads

GROWATT INVERTER SETUP

The Growatt inverters are compatible with the Hubble range of batteries, however compatibility varies depending on the inverter series. Please take special note of the ES Series Setup mentioned below. 
​
The following field guide will assist with the correct battery settings you should use.
For further detailed information ensure you read the manual of the supplied battery regarding setup and installation instructions.

GROWATT INVERTERS

Picture

 GROWATT TL SERIES INVERTER

Picture

GROWATT TL & HUBBLE LITHIUM

Picture

GROWATT ES SERIES & HUBBLE LITHIUM

Picture
Picture

GROWATT INVERTER & HUBBLE
​PRE-LAUNCH SETUP

Download the corresponding Hubble product manual and check the installation guide and pre-launch checklist.
​

GROWATT INVERTER SETTINGS

TL SERIES

The below chart settings needs to be configured for the Growat TL series of inverters, as these do not have CAN bus communications.
The below settings are the recommended settings to use for the corresponding Hubble Lithium battery.
Setup
Growatt 48V 5KW TL
​Hubble AM-2 51V
Growatt 48V TL
​Hubble AM-3 51V
Growatt 48V TL
X-101 51V
Growatt 48V
​S-100 12V (4 in series)
Battery Charge Amps
(Setting 02)
Recommend 40Amp per battery
Recommend 20Amp per battery
Recommend 40Amp per battery
Recommend 40Amp per string
Battery Type
​(Setting 05)
USE
USE
USE
USE
Voltage point back to Utility
​(Setting 12)
47V
47V
47V
48V
Voltage point back to Battery
(Setting 13)
53V
53V
53V
51V
Bulk Charge
​(Setting 19)
53.4V​
53.8V
53.4V
57.2V
Float Charge Voltage
(Setting 20)
53.4V
53.8V
53.4V
56V
Low DC Cut off
​(Setting 21)
44V
44V
44V
46V

ES SERIES SETUP

The ES series of Growatt Inverters do have CAN Bus communications.

IMPORTANT NOTE:
If you need to use the ES series with a Hubble battery and CANbus, then  it is required to install a Hubble Cloudlink.
Even though the Hubble battery can communicate directly with the Growatt, the Hubble Cloudlink has the full Growatt CAN bus protocol embedded and adds extra communications features that the Growatt requires to perform optimally.

Ensure your master battery dip switch is set to 1 to enable CAN bus communication on the Hubble battery.
​
Growatt ES Series Setup
SPF 5000ES
AM-2 / AM-3 / X-100
SPF 5000ES
​S-100 (4x S-100 in series)
Setting 05
​(Battery Type)
LI
​USE
Setting 36
Protocol 52
N/A
Voltage point back to Utility
​(Setting 12)
47V
48V
Voltage point back to Battery
(Setting 13)
53V
51V
​Bulk Charge
​(Setting 19)
​N/A (Auto setup with CAN)
57.2V
​Float Charge Voltage
(Setting 20)
​N/A (Auto setup with CAN)
56V
Low DC Cut off
​(Setting 21)
N/A (Auto setup with CAN)
46V

HUBBLE LITHIUM & GROWATT PIN LAYOUTS

Below are the Hubble BMS, Cloudlink, and Growatt side pinouts.
Note that the Hubble Lithium BMS pinouts are the same as the Cloudlink CAN pinouts.
Picture

FREQUENTLY ASKED GROWATT QUESTIONS

Q: How do you setup multiple batteries?

​A: Check the manual for a more detailed explanation. You will have to set dip switch settings per battery to give them a unique address. You also have to connect the included RJ45 battery link cables into the "Battery Link" port of each battery. Ensure your master battery dip switch 1 is on, 2,3,4 is OFF.  Only the master battery CAN Bus will be enabled. 

Q: Do I have to use the communication battery link cables if i dont want to monitor the slave batteries or have communications?

​A: Yes it is recommended to still connect the slave cables for inter BMS communicaitons.

HUBBLE DIP SWITCH SETTINGS FOR MULTIPLE BATTERY INSTALLATION

Picture
Picture
​For correct setup and communication each battery needs a unique serial address in order to communicate.
If you are only using one battery in your setup, consider this the master battery and ensure you set it to address 1.

CONTACT US

​BECOME A RESELLER

RESELLER LOGIN

Picture

VIEW OUR PRODUCTS

ABOUT HUBBLE-RIOT CLOUDLINK

SUPPORT

Copyright Hubble Lithium (pty) ltd 2020 - 2021
  • Home
  • PRODUCTS
    • Solar Lithium Batteries
    • Golf Cart Lithium Batteries
  • Inverter Guides
    • Axpert
    • Deye
    • GoodWe
    • Growatt
    • Kodak
    • Luxpower
    • Mecer
    • Microcare
    • MLT
    • Must
    • Phocos
    • SUNSYNK >
      • Sunsynk 8KW & 12KW Setup
      • Sunsynk 5KW Setup
    • Synapse
    • Victron
  • Cloudlink
    • HUBBLE Cloudlink
    • Setup Guide
    • CLOUDLINK PORTAL >
      • PORTAL LOGIN
      • CHANGE LOG
  • About
    • Team
    • News & Updates
  • Contact
  • Reseller
    • Reseller Registration
    • Reseller Access
    • Downloads