top of page
Backgrounds-02.jpg

Hubble is officially recognised and fully integrates with Luxpower inverters.

​

The following field guide will assist with the correct battery settings you should use.

​

For further detailed information ensure you read the manual of the supplied battery regarding the setup and installation instructions.

luxpower INVERTER SET UP

INVERTER example

LuxPower inverter

IMPORTANT: On the inverter, setup the charge/discharge profile AND setup the allowed charging times (P1, P2 and P3). (The default settings won’t allow the inverter to charge the battery using Mains power).

Model
Voltage
Bulk/Equalised (Vdc)
Float Voltage (Vdc)
Cutoff Voltage (Vdc)
Recommended Charge Amps
Max Discharge Current (A)
S Series
12V
14
14
12
30A
100A
X-100
48V
52.8
52.8
44
30A
100A
X-101
48V
53.8
53.8
44
30A
100A
X-200
36V
41.5
41.5
34
30A
100A
AM-2
48V
53.8
53.8
44
30A
100A
AM-3
48V
53.8
53.8
44
20A
50A
AM-4
24V
29
29
23.8
30A
100A
AM-5
48V
55.2
55.2
47
30A
100A
AM-10
48V
55.2
55.2
47
60A
150A
BLADE
48V
55.2
55.2
47
50A
200A

STEPS TO CONNECT TO THE LUXPOWER SNA5KW:

​

  1. Set Hubble MASTER dip to 1000 if AM-2 or AM-4. If AM-5 or
    AM-10 model set master dip to 0000.
     

  2. Set Hubble Slaves to their respective addresses as per manual.
     

  3. Use CAN out on MASTER to Luxpower inverter.
     

  4. On the SNA, go to the MENU.
     

  5. Select option 3 for Battery settings.
     

  6. Select Lithium battery
     

  7. Select BRAND 2

STEPS TO CONNECT THE LUXPOWER LXP5K HYBRID:

​

  1. Set Hubble MASTER dip to 1000 if AM-2 or AM-4. If AM-5 or AM-10 model set master dip to 0000.
     

  2. Set Hubble Slaves to their respective addresses as per manual.​
     

  3. Use CAN out on MASTER to Luxpower inverter.
     

  4. Go to BATTERY Settings.
     

  5. Select Lithium
     

  6. Select PYLON

Please note: Hubble Lithium recommends the Cloudlink device on Luxpower installations. It is not required but recommended.

INVERTER SETTINGS

Below are the Hubble BMS, Cloudlink, and Luxpower side pinouts.
Hubble Lithium BMS pinouts are the same as the Cloudlink CAN pinouts.

​

PLEASE NOTE: Check both the user-manual and the packaging of your inverter for its CAN pinout! Some LuxPower units use pins 4 and 5, whereas others still use pins 3 and 4.

LXP RANGE: Luxpower using pins 3 & 4

3&4 Pinlayout.png

SNA Range: Luxpower using pins 4 & 5

4&5 Pinlayout.png

HUBBLE DIP SWITCH SETTINGS FOR MULTIPLE BATTERY INSTALLATION

​

​For correct setup and communication each battery needs a unique serial address in order to communicate. If you are only using one battery in your setup, consider this the master battery and ensure you set it to address 1.

am-2

AM-2 DIP switch inverter settings

am-5 & AM-10

AM-5 &10 DIP switch inverter settings

pin layout

How do you setup multiple batteries?

 

See table above and check your product manual for a more detailed explanation. You will have to set dip switch settings per battery to give them a unique address. You also have to connect the included RJ45 battery link cables into the "Battery Link" port of each battery. Ensure your master battery dip switch 1 is on, 2,3,4 is OFF.  Only the master battery CAN Bus will be enabled. You can then connect the Hubble Cloudlink into the CAN port of the master battery for communications to work.

​

​

Do I have to use the communication battery link cables if i dont want to monitor or have communications?

 

Yes

FAQ

bottom of page